넳 넲
Home  ꄲ  Vehicle Identification System  ꄲ  Access control Accessories  ꄲ  SEC-R601 Barrier Anti-Crash Radar

SEC-R601 Barrier Anti-Crash Radar

1.Simple installation and deployment: drill holes in the cabinet for cable routing, fasten the device via mounting holes, and connect the power cable and relay cable.
2.Standard relay output, directly compatible with mainstream barrier gate controllers.
3.Supports parameter configuration via APP and miniprogram over Bluetooth; simple step-by-step operation.
4.Fast relay response, enabling timely bar halt even under rapid barlowering conditions for greater safety margin.
5.Application: Vehicle
 Product Specifications

Technical Parameter

 

Data Communication

Technology Adopted

MM Wave,FMCW

Operating Voltage(V)

DC 9-36V

Operating Temperature(℃)

-40℃~85℃

Communication Interface

Bluetooth BLE 5.0

Power Consumption(W)

<1W

Signal Output

Solid‑state relay (galvanic isolation)

Frequency Band(GHz)

60GHz

LED Indicators (LED)

Red: Power indicator

Green:Object‑detection indicator

Blue:Bluetooth connection indicator

Ingress Protection Rating

IP67

Interface Cable

4‑Pin cable, 0.15 mm², 1 m

Response Time(ms)

50ms

Detection Range

Housing Material

ABS

Detection Range

Max.2mx6 m

Housing Dimension

57.00*70.00*22.40mm

 

 

Mounting Method

M4*6 hand‑tightened screws

 

 

Installation Height

0.5‑0.6m, mounted on cabinet

 

 

Weight(g)

<100g

 

 

Output Rating

Max.36VAC/DC

 

 

Switching Current

Max.l00mA

 

 

 

Details display 

 

2

 

NO

Wire Color

Function

Description

1

Red

VCC

9V-36V DC+

2

Black

GND

9V-36V DC-

3

White

COM

Relay common output

4

Yellow

NO

Relay normally‑open output (normally connected to loop‑detect input)

 

 

Notes

Observe the following notes when using the radar:

1.Configure radar operating parameters reasonably with reference to the user manual according to on‑site conditions.

2.Select proper radar installation height; improper height (too low or too high) will cause detection failure.

3.Connect radar signal wires and barrier‑gate control interface correctly per the user manual.

4.Do NOT connect to 220 V AC power supply.

5.Bluetooth auto‑disables after 30 minutes of inactivity. Bluetooth restarts upon power‑cycle. Blue LED lights when Bluetooth connection succeeds.

Radar Installation

1.Mount the radar close to the barrier‑gate cabinet or an independent post and pay attention to mounting orientation. Installation height (distance from road surface to radar indicator): 50 cm‑60 cm. Horizontal offset: distance from radar center to barrier‑bar center: 20 cm‑25 cm.

Note: The radar shall protrude or be flush with surrounding objects. No interfering objects are allowed within 2 m to left and right sides of the radar; otherwise radar performance will be affected.

2.Drill‑and‑fasten Installation Affix positioning sticker onto cabinet. Drill holes with an 8‑mm drill bit: pass‑through cable hole and mounting holes. Thread radar cable through the central hole. Secure radar with hand‑tightened screws to prevent wobble.

3.Adhesive Mounting (Optional) Alternative to drilling: fasten radar by applying 3 M adhesive tape around its perimeter and press firmly.

4.Barrier‑Gate Wiring Connect red and black radar wires to positive and negative terminals of 9‑36 V DC power supply respectively. Connect white and yellow wires to the common terminal and loop‑detect terminal of the barrier‑gate main board.

Additional Installation Precautions

1.The barrier‑gate cabinet or independent mounting post must be rigidly secured. Cabinet / post vibration will trigger abnormal radar detection.

2.Repair severely deformed barrier bars; bar deformation causes false radar detections.

3.If license‑plate‑recognition cameras or large metal objects sit in front of radar field‑of‑view, install radar on a separate post.

4.Avoid deployment on road surfaces with numerous manhole covers / metal rails. Small‑area metal features are acceptable but require confirmation from manufacturer.

5.For scenarios with large vehicle approach angles (sharp diagonal entry / exit), guide vehicle trajectories using traffic cones and consult manufacturer technical support. Radar is not recommended for sharp‑corner sites.

6.For advertising bars, fence‑type bars and overhead barrier gates, mount radar on the incoming‑traffic side. When barrier bar has descended more than 45 %, detection for intruding objects becomes less sensitive.

Radar Commissioning

1.Install Bluetooth APP: simpleDemo‑release.apk

Enable phone Bluetooth and location permissions before launching APP. Grant Bluetooth and location access permissions when prompted. Navigate to connection page and tap “Connect Bluetooth Device”.

2.Connect to Radar

Tap “Connect Bluetooth Device”, then tap the discovered radar model to establish connection. The numeric suffix e.g. [-73] after radar model represents signal strength. Among multiple discovered radars, smaller number means closer distance to mobile phone.

                                                             

Connection Failure Troubleshooting:

a. Verify the APP has obtained Bluetooth and location permissions on mobile device.

b. Power-cycle radar and retry connection.

3.Radar Configuration (Complete these steps for normal operation; most scenarios require no further adjustment) Tap “Configuration”.

Step 1: Select vehiclepass type and barrier-bar type.

                                                  

Step 2:Set bar length. Set configured length to 0.5 m shorter than actual physical bar length (recommended).

Step 3: Tap “Save Radar Configuration”.

Step 4: Raise barrier bar. Ensure no persons or objects enter within 2 m left-and-right of radar. Tap “Bar-Raise Background Learning” in APP / mini-program until learning completes.

Step 5: Again ensure no persons or objects within 2 m left-and-right of radar. Tap “Bar Motion Learning”. Operate barrier bar to cycle up-and-down repeatedly via remote control until learning completes.

                                                   

Step 6: Lower barrier bar fully. Radar performs self-learning. Keep 2-m clear zone left-and-right until self-learning finishes. Commissioning is now complete and radar is operational.

Note: If “vehicle-pass type” or “barrier-bar type” are modified, always perform Step 3 “Save Radar Configuration” first to avoid malfunction.

4.Advanced Settings

For special-site requirements such as person-vehicle discrimination or sensitivity adjustment: tap “More” then “Advanced Settings”. Save radar configuration after adjustment. Functions include radar reboot and factory-default restoration.

                   

Other products